Join Us ::

Menu Home Classes GK Engineering Past Papers Current Affairs Technical GAT Subject Programming Medical Papers

GAT Subject :: All Aptitude Test ::

Home » GAT Subject » Aptitude Test - 187
Hassan
1.People overcome natural language problems by:
A. grouping attributes into frames
B. understanding ideas in context
C. identifying with familiar situations
D. grouping attributes into frames
2.The Cedar, BBN Butterfly, Cosmic Cube and Hypercube machine can be characterized as
A. SISD
B. MIMD
C. SIMD
D. SISD
3.From what location are the 1st computer instructions available on boot up?
A. ROM BIOS
B. CPU
C. boot.ini
D. ROM BIOS
4.What could cause a fixed disk error.
A. No-CD installed
B. bad ram
C. slow processor
D. No-CD installed
5.Missing slot covers on a computer can cause?
A. over heat
B. power surges
C. EMI.
D. over heat
6.When installing PCI NICS you can check the IRQ availability by looking at
A. dip switches
B. CONFIG.SYS
C. jumper settings
D. dip switches
7.With respect to a network interface card, the term 10/100 refers to
A. protocol speed
B. a fiber speed
C. megabits per seconds
D. protocol speed
8.Which Motherboard form factor uses one 20 pin connector
A. ATX
B. AT
C. BABY AT
D. ATX
9.A hard disk is divided into tracks which are further subdivided into:
A. clusters
B. sectors
C. vectors
D. clusters
10.A wrist grounding strap contains which of the following:
A. Surge protector
B. Capacitor
C. Voltmeter
D. Surge protector
11.Which standard govern parallel communications?
A. RS232
B. RS-232a
C. CAT 5
D. RS232
12.In laser printer technology, what happens during the conditioning stage?
A. The corona wire places a uniform positive charge on the paper
B. A uniform negative charge is placed on the photosensitive drum
C. A uniform negative charge is placed on the toner
D. The corona wire places a uniform positive charge on the paper
13.What product is used to clean smudged keys on a keyboard?
A. TMC solvent
B. Silicone spray
C. Denatured alcohol
D. TMC solvent
14.ESD would cause the most damage to which component?
A. Power supply
B. Expansion board
C. Monitor
D. Power supply
15.Which type of system board is the MOST likely candidate for processor upgrading if you want maximum performance and future compatibility?
A. ML
B. PCI
C. ISA
D. ML
16.Suppose that you have a the maintenance package identifies several possible field replaceable units (FRUs) that will resolve the problem. What should you do after turning the power off?
A. Replace the indicated parts, one at a time in the recommended sequence, until the problem is resolved; return unused FRUs to stock
B. Replace all of the indicated FRUs at once and return the machine to the customer if the problem is resolved
C. Follow the same procedure as in ays replace the system board first if it is on the list of possible FRUs If multiple FRUs are indicated, then software is the most likely source of the problem
D. Replace the indicated parts, one at a time in the recommended sequence, until the problem is resolved; return unused FRUs to stock
17.Which peripheral port provides the FASTEST throughput to laser printers?
A. RS-232
B. SCSI
C. Parallel
D. RS-232
18.The mouse pointer moves erratically, what is the possible cause? The mouse
A. ball is dirty
B. is not connected
C. driver is not installed properly
D. ball is dirty
19.Voltage is measured:
A. in parallel
B. in series
C. after breaking the circuit
D. in parallel
20.Your customer tells you the print quality of their dot matrix printer is light then dark. Which of the following could cause the problem.
A. Paper slippage
B. Improper ribbon advancement
C. Paper thickness
D. Paper slippage
21.The 34-pin connection on an I/O card is for?
A. Floppy drive
B. SCSI drive
C. IDE drive
D. Floppy drive
22.The terms "red book", "yellow book", and "orange book" refer to:
A. SCSI
B. ide
C. floppy drive technology
D. SCSI
23.On the 16-bit ISA bus, IRQ2 is elevated to which higher level Interrupt?
A. 9
B. 11
C. 13
D. 9
24.What beep codes could indicate a system board or power supply failure?
A. steady short beep
B. no beep
C. one long continuous beep tone
D. steady short beep
25.Which part of the laser printer should NOT be exposed to sunlight?
A. Transfer corona assembly
B. PC drum
C. Primary corona wire
D. Transfer corona assembly
26.After doing a low-level format, what would be the next step in configuring the hard drive in a system?
A. Format DOS partition
B. Install operating system
C. Configure DMA channel and back-up interrupt
D. Format DOS partition
27.Resistance is measured in ?
A. Volts
B. Amps
C. Watts
D. Volts
28.What command is used to reset a MODEM when using the "AT Command Set"?
A. ATR
B. ATZ
C. DTR
D. ATR
29.When installing a SCSI CD-ROM drive, you must set the CD-ROM SCSI adapter to:
A. B0007
B. An unused SCSI address
C. The same address as the SCSI device before the CD-ROM
D. B0007
30.Pick the correct choice for the 80386SXCPU.
A. 16 bit word size, 16 bit data path
B. 32 bit word size, 16 bit data path
C. 8 bit word size, 32 bit data path
D. 16 bit word size, 16 bit data path
Related Subjects

Date to Date Current Affairs 2022

PakMCQs.net

Quick Links

GAT Subject



   Computer Science    English Mcqs    Agriculture    

Engineering



   Computer Science    Civil Engineering    

Technical



   Networking    Electronics    Database    

Past Papers



   Model Papers    FPSC Papers    
Our Team | Career | Contact | JoinUs | Privacy Policy | DMC

© 2020-2024 by Pak-MCQs.net All Rights Reserved.

Email: [email protected]